When choosing between the Arcan A20019 and the Jack Boss 3 Ton, the deciding factor for most garage mechanics comes down to chassis composition versus hydraulic lifting mechanism. The Arcan floor jack uses an all-aluminum aircraft-grade construction tailored for lower clearances and lightweight positioning, whereas the Jack Boss unit pairs a welded steel and aluminum hybrid frame with a dual-piston pump designed for rapid lifting under load.
Choose the Arcan A20019 if you service low-profile sports cars and prioritize a lighter, fully aluminum chassis with side positioning handles. Select the Jack Boss 3 Ton if you maintain heavier crossover platforms or utility vehicles and want faster saddle rise from a dual-piston hydraulic assembly backed by documented overload testing.
Arcan A20019 vs Jack Boss 3 Ton at a Glance
| Feature | Arcan A20019 | Jack Boss 3 Ton |
|---|---|---|
| Rated Capacity | 3 Tons (6,000 lbs) | 3 Tons (6,600 lbs) |
| Chassis Material | Aircraft-grade aluminum | Aluminum body with welded steel frame |
| Minimum Saddle Height | 3.75 inches | 3-15/16 inches (approx. 3.94 inches) |
| Maximum Lift Height | 18.0 inches | 18-5/16 inches (approx. 18.31 inches) |
| Hydraulic Pump Style | Quick-rise single mechanism | Dual-piston quick lift pump |
| Total Unit Weight | 56.0 pounds | 58.5 pounds |
| Safety Certifications & Testing | Bypass and overload valves | 1.5X overload tested (4.5 tons), ANSI/ASME PASE |
| Included Saddle Pad | Not listed | Large rubber saddle included |
| Chassis Dimensions | 30 x 13.5 x 8 inches | 28.3 x 13.7 x 7.8 inches |
| Best For | Low-clearance sports cars & track transport | Multi-vehicle garages & swift SUV maintenance |
Chassis Construction and Material Durability
Chassis composition dictates how well a floor jack withstands torsional stress when lifting heavy loads on uneven workshop concrete. The Arcan A20019 aluminum floor jack is built around an aircraft-grade aluminum frame with a reinforced lift arm. This reinforcement is engineered specifically to prevent arm twisting and to preserve torsional stability when jacking up to its 6,000-pound limit. Because the frame relies entirely on structural aluminum, it naturally resists corrosion from winter moisture and road brine tracked into the garage, while remaining rigid through prolonged shop duties.
By contrast, the Jack Boss 3 Ton floor jack uses a hybrid architecture that combines a high-strength aluminum body with a heavy-duty welded steel frame. Instead of relying solely on thick aluminum plate, Jack Boss incorporates steel along high-stress structural pathways and integrates steel casters beneath the chassis. This hybrid method leverages steel for ultimate shear resistance and weld rigidity, while aluminum side plates help control overall mass. In a comparison like the arcan a20019 vs torin big red, you often evaluate pure steel against pure aluminum, but here Jack Boss delivers a direct compromise between both structural philosophies.
The practical trade-off centers on wear resistance versus weight savings. The hybrid frame of the Jack Boss provides exceptional resilience against frame flexing when handling off-center vehicle picks, supported by steel front and rear rolling hardware. Arcan leans into structural aluminum extrusion, offering cleaner machining and fewer corrosion concerns over decades of use. Both units deliver industrial rigidity, but the Jack Boss frame incorporates steel reinforcement where repetitive high-load stresses occur most frequently.
Edge: Jack Boss 3 Ton for its welded steel sub-frame reinforcement and steel rolling hardware.
Lifting Range and Low-Clearance Access
A floor jack must slip underneath vehicle crossmembers or rocker pinch welds without scraping side skirts, while still extending high enough to place jack stands under tall chassis rails. Evaluating the Arcan A20019 or Jack Boss 3 Ton for low clearance reveals meaningful differences in both starting saddle profile and maximum vertical reach. The Arcan A20019 minimum height sits at a low 3.75 inches according to its product description (with alternate listing dimensional references placing chassis points at 11.62 inches). Its front roller and forward lift arm sweep low to reach deep center lifting spots beneath lowered suspension setups.
The Jack Boss 3 Ton lift range spans from a minimum saddle height of 3-15/16 inches (3.94 inches, or 10 centimeters) up to a maximum elevation of 18-5/16 inches (18.31 inches). While the starting height on the Jack Boss sits roughly three-sixteenths of an inch taller than Arcan’s lowest point, it counterbalances this clearance gap with greater total lift height. For readers researching an arcan a20019 vs daytona 3 ton, vertical reach often dictates whether a jack can handle tall utility vehicles without wood blocks, and the Jack Boss reaches 5/16 of an inch higher than Arcan’s 18.0-inch cap.
For vehicles with aggressive aftermarket splitters or sports suspension packages, Arcan’s 3.75-inch minimum saddle provides vital breathing room to slide beneath forward crossmembers without requiring drive-on ramps. If you routinely work on stock passenger sedans, minivans, or light crossovers, the slightly taller stance of the Jack Boss will slide under factory lift points effortlessly while offering extra headroom at full cylinder extension.
Edge: Arcan A20019 for its lower 3.75-inch minimum saddle height under low-slung chassis.
Pump Mechanism and Lifting Speed
Hydraulic efficiency directly impacts how long you spend pumping a handle before a vehicle tire leaves the ground. The Jack Boss 3 Ton dual pump system uses twin hydraulic pistons positioned side by side at the base of the handle yolk. Each stroke of the handle displaces double the fluid volume compared to traditional single-action pumps. As a result, the saddle rises to the vehicle frame rail in just a few unloaded handle pumps, transitioning rapidly into pressurized vehicle elevation.
The Arcan A20019 relies on a quick-rise hydraulic system designed to swiftly raise the saddle to the vehicle load, reducing the initial pumping required during setup. Its hydraulic circuit features internal bypass and overload valves to protect the ram against over-extension and excessive line pressure. While the quick-rise design works smoothly, the listing does not designate a dual-piston layout for the A20019. In similar assessments such as the jack boss 3 ton vs torin big red, dual-piston assemblies consistently raise heavy vehicle chassis with fewer total handle strokes than single-ram mechanisms.
This difference in hydraulic architecture translates to real physical exertion over a multi-tire rotation. The dual-piston assembly on the Jack Boss requires less repetitive handle pumping to move from resting height to the vehicle chassis. Arcan’s hydraulic valving delivers steady, controlled ascents, but the Jack Boss clearly prioritizes cycle speed for busy home mechanics.
Edge: Jack Boss 3 Ton for its dual-piston pump that minimizes handle strokes.
Weight, Transport, and Shop Maneuverability
Moving a floor jack around tight garage stalls or loading it into a vehicle trunk requires manageable chassis weight and ergonomic lifting points. Looking at the Arcan A20019 vs Jack Boss 3 Ton weight, the two models stay remarkably close despite their material differences. The Arcan A20019 weighs exactly 56 pounds, made manageable by aircraft-grade aluminum plates and integrated side-mount positioning handles. These side handles allow mechanics to pick up the jack two-handed or maneuver the frame into position under a car without pulling exclusively on the pump handle.
The Jack Boss 3 Ton checks in at 58.5 pounds, adding just 2.5 pounds over the Arcan despite incorporating a welded steel sub-frame. Its mobility relies on smooth-rolling steel casters and front swivel casters paired with a sturdy two-piece handle. Mechanics comparing models in the daytona 3 ton vs jack boss 3 ton bracket know that steel jacks often weigh upwards of 70 to 100 pounds, making both of these units remarkably portable by industry standards.
Arcan takes the advantage in physical handling due to its lighter 56-pound body and dedicated side-mount carrying handles. When you need to load a jack into an SUV cargo area for track-day tire changes or shift it across an unpaved shop threshold, those built-in grab handles provide much better leverage than grasping bare side plates.
Edge: Arcan A20019 for its 56-pound mass and ergonomic side-mount positioning handles.
Safety Testing, Load Ratings, and Vehicle Care
Safety certifications and load ratings determine long-term peace of mind when raising thousands of pounds of rolling machinery. In an objective Jack Boss 3 Ton review, safety verifications stand out prominently: Jack Boss subjects this model to 1.5X factory overload testing up to 4.5 tons (9,900 pounds) to guarantee hydraulic and structural integrity under stress. It also complies with recognized ANSI/ASME PASE safety standards. Furthermore, Jack Boss lists its maximum capacity as 3 tons (specified in listing text as 6,600 lbs), giving users a wide margin of structural confidence.
Arcan rates the A20019 at 3 tons (6,000 pounds), which covers a broad spectrum of passenger vehicles, mid-size SUVs, and light trucks. To safeguard against hydraulic failure, Arcan includes built-in bypass valves that prevent the ram from over-extending, as well as an internal overload valve that stops operation if an operator attempts to lift beyond capacity. For users evaluating the arcan a20019 vs pittsburgh 3 ton, these standard hydraulic safeguards represent a proven design baseline.
Beyond structural testing, vehicle body protection separates the two. Jack Boss ships with a large rubber saddle pad directly on the lifting cup, preventing metal-on-metal contact against delicate pinch welds, painted subframes, and coated underbody panels. The Arcan A20019 listing mentions a floor jack with handle but does not specify an included rubber saddle pad, meaning users may need to source aftermarket pads to prevent scratching chassis coating.
Edge: Jack Boss 3 Ton for its 1.5X overload proof test, ANSI/ASME PASE compliance, and included rubber saddle.
Pros and Cons
Arcan A20019
Pros
- Low 3.75-inch minimum saddle height
- Lightweight 56-pound aluminum frame
- Side-mount handles for easy positioning
- Corrosion-resistant aircraft-grade aluminum
Cons
- Listing does not include rubber saddle pad
- Lower maximum lift height at 18 inches
Jack Boss 3 Ton
Pros
- Dual-piston pump accelerates lifting speed
- Tested to 1.5X overload rating
- Reaches 18-5/16 inches maximum lift
- Includes protective rubber saddle pad
Cons
- Slightly taller 3-15/16-inch minimum height
- Heavier at 58.5 pounds
View Jack Boss 3 Ton on Amazon
Who Should Buy Each One
Choose the Arcan A20019 If
- You own lowered passenger cars or sports coupes requiring an ultra-low 3.75-inch starting saddle clearance.
- You frequently transport your floor jack to track days or mobile work sites and want side-mount handles for easy loading.
- You prefer a complete aircraft-grade aluminum chassis that offers superior resistance to ambient garage moisture and road salt.
- You want a lightweight 56-pound chassis designed specifically for nimble positioning in confined shop spaces.
Choose the Jack Boss 3 Ton If
- You want maximum lifting speed achieved by a dual-piston hydraulic pump mechanism.
- You maintain a fleet of taller vehicles, including SUVs, minivans, and travel trailers requiring up to 18-5/16 inches of lift.
- You value third-party verified ANSI/ASME PASE compliance and rigorous 1.5X factory proof-load testing to 9,900 pounds.
- You want an included protective rubber saddle pad to prevent marring factory pinch welds right out of the box.
Final Verdict
For most everyday home garages and multi-vehicle households, the Jack Boss 3 Ton represents the more capable all-around lifting tool. Its dual-piston pump noticeably accelerates the lifting process, its hybrid steel-and-aluminum frame provides reinforced structural rigidity, and its 18-5/16-inch maximum lift height handles taller SUVs and trailers with ease. Factor in documented ANSI/ASME PASE safety compliance, 1.5X overload factory testing to 9,900 pounds, and an included rubber saddle, and the Jack Boss edges ahead in all-purpose garage utility.
However, the Arcan A20019 remains the superior choice for automotive enthusiasts maintaining low-clearance performance vehicles. With a minimum saddle height of 3.75 inches, an all-aluminum frame weighing just 56 pounds, and dedicated side-mount handles, it excels at slipping under tight side skirts and sliding easily across workshop floors. If low ground clearance and transport convenience are your primary pain points, the Arcan A20019 is built specifically for your garage.
FAQ
What is the Arcan A20019 minimum height compared to the Jack Boss?
The Arcan A20019 features a low-profile minimum saddle height of 3.75 inches according to its product description, making it well-suited for lowered passenger cars. The Jack Boss 3 Ton has a minimum saddle height of 3-15/16 inches (approximately 3.94 inches or 10 centimeters), which is about 3/16 of an inch taller than the Arcan.
Does the Jack Boss 3 Ton feature a dual pump mechanism?
Yes, the Jack Boss 3 Ton is equipped with a dual-piston quick lift pump. This hydraulic setup displaces more fluid with each stroke of the handle, reducing the overall number of pumps needed to raise the saddle to the vehicle chassis.
Between the Arcan A20019 or Jack Boss 3 Ton for low clearance, which fits better?
The Arcan A20019 is the better option for exceptionally low vehicles because its 3.75-inch minimum height sits slightly lower than the 3-15/16-inch saddle of the Jack Boss. That slight clearance difference can make an impact when navigating beneath sports car splitters and aftermarket ground effects.
What is the Arcan A20019 vs Jack Boss 3 Ton weight difference?
The Arcan A20019 weighs 56 pounds, while the Jack Boss 3 Ton weighs 58.5 pounds. Despite featuring a welded steel sub-frame alongside its aluminum body, the Jack Boss is only 2.5 pounds heavier than the full-aluminum Arcan.
Is Jack Boss 3 Ton worth it for SUV and truck owners?
The Jack Boss 3 Ton is well-suited for SUVs, minivans, station wagons, and light trailers thanks to its 18-5/16-inch maximum lift height and 3-ton capacity. Its dual pistons allow users to elevate larger vehicles quickly without excessive handle pumping.
Does either model include a protective rubber saddle pad?
The Jack Boss 3 Ton listing explicitly states that it includes a large rubber saddle pad to protect vehicle lift points and pinch welds from scratches. The Arcan A20019 product listing mentions the jack and handle as included components but does not specify a rubber saddle pad.
What safety certifications and overload valves are included on these jacks?
The Jack Boss 3 Ton is 1.5X overload tested to 4.5 tons (9,900 pounds) and meets ANSI/ASME PASE safety standards. The Arcan A20019 includes internal hydraulic bypass and overload valves to prevent ram over-extension and avoid operating past its 6,000-pound rated capacity.
